Plans for Making Full Extension Wood Drawer Slides

This is your complete guide on how to build a drawer. See all the tips and tricks you lot need to know to build perfect drawers every time – fifty-fifty for beginners!

Pivot THIS TO PINTEREST

Building drawers are most like a rite of passage going from beginner woodworker to more than intermediate woodworker.

I won't lie.

Building drawers even so stress me out – every single time!

But I don't attempt to stay abroad from them anymore.

My journey learning to build drawers –

The very first fourth dimension I built a drawer was for this X-leg accent table. I was just then glad it didn't use drawer slides because that would have been completely unforgiving to being even slightly off square. (Goes to show how little conviction I had in my builds ;))

The next build that used drawers Clara bedside table. It took me forever and 3 versions of the drawer box to finally get that one drawer to piece of work!

Then came the mirrored console tabular array. I had built upwards a bit of confidence to get the drawers to piece of work… but unfortunately, that would not exist the case.

After spending ii full days trying to become the drawers to work, I gave in and bought lesser mount drawer slides which were forgiving to the drawers beingness off-foursquare.

Then came the Emerson buffet and it changed my life! I mean my drawer edifice life. I was extra super duper careful from the very beginning nigh keeping everything super duper square and information technology worked!!

The very first time!!

Well, at least 1 of them did. The other one had to go through a few modifications earlier it worked.

But that was progress… and afterwards that, I have been getting meliorate and better at drawers!

I recently congenital the huge Barn door storage cabinet with iv drawers and they all worked the very starting time time!

I call back I take finally discovered the piddling tips and tricks that make building drawers foolproof!

***This postal service contains affiliate or referral links. It is a mode for this site to earn advertisement fees past advertizement or linking to sure products and/or services. Please read my full disclosure here ***

How to build a sliding drawer using Kreg Jig

Building a drawer box using a Kreg Jig is very straightforward and like shooting fish in a barrel. I am assuming you are using ¾" thick stock.

• Decide the dimensions of the drawer box. You lot accept to take into account the size of the drawer slides and decide the width accordingly. The drawer slide should come up with data on that.
• Subtract 1½" from the width to come upward with the size of wood to cute for the width. The depth of the drawer box volition depend on the project.
• Cut opposite sides the same verbal lengths. This is VERY important. Measure 4 times, cutting in one case.
• Build the drawer box using woods glue and one ¼" pocket hole screws keeping all the sides square. Meet below for tips and tricks to make this foolproof.
• Glue and nail a ¼" plywood base cut to size of the drawer box. This is the drawer box base.
• Attach the drawer slides to the drawer box and the cabinet frame.
• Adhere the drawer face leaving ⅛″ gap on all sides using wood gum and finish nails and clamp information technology well.

Pivot THIS TO PINTEREST

Although I am using a Kreg Jig to build this drawer, the basic principles are the same using whatsoever other joinery method.

RELATED: How to employ a Kreg Jig

Now that y'all know the basics of how to build a elementary drawer, allow'due south talk virtually making information technology super easy to bet it square and installed in no time!

Tips and tricks to build and install perfect drawers –

It is not just almost edifice the perfect drawer. It is likewise about getting it all washed fast!

1. Measure 4 times, cut once

I know you have heard this a lot merely practice you always follow it one hundred percent?

Or maybe information technology might be but me considering when I am too tired or running backside on a project, I only go for it. I have learned the difficult fashion to non practise that ever!

2. Apply an assembly square

Using an assembly foursquare to build the projection makes a huge difference in making certain everything is square in the cabinet and gear up for the drawers! Also, the right angle clench from Kreg is very useful too!

3. Employ a  corner clamping jig

You could build your corner jig using chip wood or get this corner clamping jig which has been the best addition to my workshop!

I use this along with the assembly foursquare to build drawer boxes to ensure that they are perfectly square every single fourth dimension!

4. Attach drawer base Before removing the corner jig

You built the perfect square drawer simply when you lot install the base, it goes out of square. It happens!

I have had this happen a couple of times. So make sure to attach the base to the drawer box while the corner clamping jig is still belongings the drawer together!

5. Use a drawer slide jig to attach the drawer slides

Remember we are talking well-nigh making everything quick and foolproof?

I love this drawer slide jig! It makes installing drawer slides and so easy! Kickoff, you clamp them to the chiffonier frame and install the slides.

Then, rest the drawer on the jig on both sides, extend the slide and attach to the drawer. That is it!!

The simply measuring yous need to do is where to install the slide on the chiffonier. No levels needed either!

half dozen. Use the playing card fob

The drawer is in and adjacent is the drawer face up. The drawer face up should have a ⅛″gap around it for smoothen operation.

To make sure it holds up, I utilise this trick I read well-nigh a long time ago – use playing cards. Well-nigh seven playing cards make the ⅛″ thickness and 52 playing cards requite you lots of equal spacers for any build!

No playing card? Try these reusable spacers. I dearest using these for diverse projects!

7. Use a hardware jig to adhere hardware

This last tip isn't exactly specific to drawers just I wish I had discovered this hardware jig before installing all the knobs and pulls I have in the past. Information technology made installing the hardware super easy and perfect!

So, in that location you have it… my entire encephalon dump on how to build a drawer and install it quickly and perfectly!

I promise you find these tricks and tips helpful! Practise you lot accept any specific tricks that I might have missed? Share in the comments!

PIN THIS TO PINTEREST

Materials

• Lumber as needed to build project
• Drawer slides as needed by project. I like full extension brawl bearing slides.

Instructions

1. Make up one's mind the dimensions of the drawer box. You have to take into account the size of the drawer slides and decide the width accordingly. Check drawer slide packaging for this data.
   
2. If using ¾" stock, subtract i½" from the width to come up up with the size of forest to cute for the width. The depth of the drawer box will depend on the project.
   
3. Cut opposite sides the aforementioned verbal lengths. This is VERY important. Mensurate iv times, cut once.
   
4. Build the drawer box using wood mucilage and i ¼" pocket pigsty screws keeping all the sides square. Use a corner assembly foursquare for this or a Corner clamp.
   
5. Glue and smash a ¼" plywood base cut to size of the drawer box. This is the drawer box base.
   
6. Adhere the drawer slides to the drawer box and the chiffonier frame. A drawer slide jig is really helpful to install the drawers chop-chop and level.
   
7. Attach the drawer confront leaving ⅛" gap on all sides using wood glue and finish nails and clamp information technology well. See the playing card play a joke on above!

Notes

These instructions are based on using ¾" stock.

Reader Interactions

rodrigueztary1941.blogspot.com

Source: https://www.anikasdiylife.com/how-to-build-a-drawer/

Bagikan Artikel ini